Whether you’re setting up your first LED dance costume or preparing for a professional stage performance, this guide covers everything you need to know about run LED lighting sequence PC LED Player. Light Dance Pro has helped hundreds of performers worldwide create stunning synchronized light shows — and this step-by-step tutorial will help you do the same.
This guide outlines the steps required to connect, synchronize, and operate your LED lighting sequences using the PC LED Player.
Step 1. Initial Connection and Application Setup
This phase ensures the PC LED Player is running and properly connected to the LED suits.
-
Open the PC LED Player: Software would be provided after purchase any LED suits/props.
-
Verify Automatic Connection: If the Wi-Fi and the suits/props have been set up, the LED suits and controller should connect automatically at this moment.
-
Identify Transmitter: If using the transmitter, you will find a device with ID 0, which is the transmitter itself.
-
Switch Connectivity (Optional): If you want to change the connection method to Wi-Fi mode, you could press the button ” 433/wifi” at the bottom left corner.
Step 2. Creating and Utilizing Checkpoints
Checkpoints are essential tools used for synchronizing the LED effects with music or marking the start and end of specific light effects.
-
Determine Precise Timing: You usually go to Vixen to get the precise time when the LED effects begin (e.g., 10.3 seconds).
-
Access Checkpoint Editor: Back in the PC LED Player , navigate to file and then edit on the toolbar.
-
Generate Checkpoints: You can add checkpoints by increasing the number in the box, which will generate empty checkpoints below.
-
Input and Save Data: Input the time you just marked and rename the checkpoint (e.g., this is the start of the demo). Click save , and the checkpoints will be shown on the right.
Step 3. Basic Sequence Playback and Synchronization
Once checkpoints are set, you can initiate the sequence and perform real-time timing adjustments.
-
Start Playback: When the music hits the starting point, click the play button.
-
Speed Up Effect: If you miss the timing because the effect is running later than the music, you can hit the plus sign (+) button on the keyboard to speed up the light effect to match the timing.
-
Slow Down Effect: Conversely, press the minus sign (-) button to slow down the effect.
Step 4. Advanced Sequence Operations
The PC LED Player supports several functions for advanced show control, looping, and brightness adjustments.
-
Freezing the Effect: To hold the light effect after the show (e.g., for photo opportunities), locate the desired checkpoint (such as the white light checkpoint created earlier). Click the freeze button in the same row, and the effect will be held.
-
Looping a Section: For taking reels or Boomerang videos, you can loop a section of the LED effect.
-
Go to the starting checkpoint, right-click on the play button, and select set start.
-
Then go to the other checkpoint and select set end.
-
Click the play button of the starting checkpoint to initiate the looping effect.
- Switching Sequence Pages: To switch the control page for another effect (e.g., using effects from a previous show, or for freestyle dance sections), go to the select list below and choose the one you want.
- Brightness Control: At the bottom right area of the PC LED Player , you could find a slide bar for brightness. You can change the value there, with examples including 1%, 15%, and 50% brightness levels.
Pro Tips from the LDP Team:
- Always test your full setup at least 24 hours before a live performance to allow time for troubleshooting.
- Keep a spare battery fully charged as backup — especially for outdoor or extended performances.
- Label your SD cards and cables by suit number to avoid mix-ups during quick costume changes.
Frequently Asked Questions
How do I sync LED effects to music timing?
Use checkpoints in PC LED Player to mark precise moments (e.g., 10.3 seconds). During playback, use the + key to speed up or - key to slow down the effect to match the music.
Can I loop a section of my LED sequence?
Yes. Right-click the play button on the start checkpoint and select ‘Set Start’, then do the same for the end checkpoint. Click the start checkpoint play button to loop that section.
How do I freeze LED effects for photos?
Navigate to the checkpoint you want to hold (e.g., the white light effect), then click the Freeze button in that row. The LED effect will stay static until you resume playback.
Ready to start your LED dance journey?
Explore our full range of programmable LED costumes, props, and control systems.
